Dental Light Cure Composite Resin A1 A2 A3 A3.5 B1 B2 /Etching Gel/Adhesive Kits

Description

Introduction
Composite Resin A1, A2, A3, A3.5,B1,B2
All Class of direct restoration for anterior and posterior.
Indirect restoration such as Veneer,inlay and onlay.
Core buildups.
Advantages:
Solution of simplicity with universal shade
The shade of DX.Universal Composite matches with VITA classic shade guide. Therefore single shade restoration can be applied as conventional & ordinary solution.
Nano hybrid technology
DX.Universal composite is applying unique nano hybrid dispersion technology to maximize the load of fillers by controlling the size and distribution of particles. It dramatically increased composite physical properties and notably improved the smooth surface of restoration in comparision with traditional micro hybrid or hybrid composite.
High Radiopaque.
Fluoride releasing to prevent recurrent caries.
Excellent handling.
Extensive indications that suitable for most cases of restorations.
Color Available: A1, A2, A3, A3.5,B1,B2
Etching Gel 37% Phosphoric Acid
Dentex etching gel is a polymer thickened gel for use on enamel and dentin.
This gel will effectively treat enamel and dentin, producing the necessary microretentive surface for successful bonding. The polymer thickener creates thixotropic properties, enhancing handling characteristics. The etchant rinse away cleanly and quickly, leaving no residue.
Packages: Refill: 5 ml/syringe, Instruction X1
Indications: Treat dentin and enamel, Treating agent on dental restorative material.
1. Isolate tooth and then prepare the cavity in a conservative manner. clean the entire surface with a slurry of pumice and water.
2. Apply etchant using a tip, a disposable syringe tip, or disposable brush tip. allow etchant to remain in palce for 15 seconds. etching time should be monitored with a stopwatch. begin timing at the end of application.
Option: place etchant enamel first, then proceed to cover dentin, for a slightly longer enamel etching time.
3. Rinse thoroughly (at least 5 seconds) to completely remover all traces of etchant.
4. Remove exces moisture from the tooth and proceed with the application of etching gel, waiting for 10 seconds, then rise thoroughly. then apply adhesive
Dentin Enamel Resins Bonding Adhesive
5th generation adhesive for all classes of direct restoration.
Post and core bonding.
Ceramic veneer/crown/inlay and other indirect restoration bondings.
Advantages:
High bonding strength and long lasting durability.
Easy infiltrate to dentin tubules.Reduce the risk of post-operative sensitivity.
Compatible with all light cure restoratives.
Time saving and easy to use.
Usage:
Enamel bonding :30 seconds DX.Etch37 etch on enamel then apply 5th generation adhesive.
Dentin bonding:15 seconds DX.Etch37 etch on dentin then apply 5th generation adhesive.
Package:5ml/Bottle
5 Resins+Etch 37%+Bonding
INDICATIONS FOR USE:
Direct restoration for all class caries.
Restoration of teeth defect and veneer.
Package:
REFILL:
Light Cure Composite: 4g/Syringe*5
Syringe Needles : 5pcs/ box*1
Total Etching Adhesive: 5ml/Bottle*1
Etching Gel: 2.5ml/Syringe*1
Applicators Brushes: 20pcs/box*1
Net weight:
188.4g
COLOR:
A1,A2,A3,A3.5,B1
FEATURES & ADVANTAGES:
Unique dispersion technology ensure the filler evenly distributed
Radioopaque and fluoride releasing Optimal polishability and high shade stability.
Excellent handling, not sticky to instrument;
Suitable for most cases of restoration, extensive indication of usage.
INSTRUCTIONS
：
(1)Preparation: isolate and prepare tooth.
(2)Cleaning: rinse the preparation with water.
(3)Drying: gently air dry until there is no visible water.Do not allow enamel or dentin to dry for an excessive period of time.
(4)Applying Dentex Self-Etching Light Cure Adhesive (DSA):
dispense 1-2 drops of DSA into a mixing well, apply enough DSA to the entire preparation with a little brush until a shiny surface is achieved and then wait for 10 seconds (DSA should not be applied too much ). Use a gentle stream of air to evaporate the solvent for 5 seconds. (If using a non self-etching adhesive, an etching step should be used according to the manufacturer's instruction).
(5)Cure: light cure for 20 seconds at 500±50mW/cm2. Keep the distance to exposure surface less than 4 mm.
(6)Applying Dentex light cure composite (DLC): place selected DLC into cavity preparation following by light cure. According to following table, the curing time is recommended for different depth and color shades. In order to reduce shrinkage stress, for a large cavity, an increment filling is recommended. In general, 1-2 mm increments are placed into cavity preparation from different sides and the restoration is built incrementally. Each increment is light cured for 30 seconds.
(7) Finishing: after light cure, adjust restoration.
(8) Polishing: use polishing strip or disc to polish the surface
WARNING:
Do not use this product for patient who is allergy to methylmethacrylate. Do not use this product with any material contained eugenol.
PRECAUTIONS:
Methmethacrylate resins may cause skin sensitization in susceptible persons. In case of contact, wash skin with soap and water. In severe situation, get medical attention.
ATTENTION:
To an exposed pulp, a pulp capping material such as Calcium hydroxide may be used before using this product.
STORAGE:
Store at 25℃ or less in a cool and dry place and avoid direct sun exposure.
Recap the syringe after use.
DISPOSAL:
After the product is used up, dispose it as normal medical rubbish.
SHELF LIFE:
3 years
A2+ICL+IBU+ IAM Sets
INDICATIONS FOR USE:
Direct restoration for all class caries.
Restoration of teeth defect and veneer.
Package:
Light Cure Composite: 4g/Syringe*5
Syringe Needles : 5pcs/ box*1
total-etching Adhesive: 3ml/Bottle*1
phosphoric acid etchant (37%): 2.5ml/Syringe*1
Applicators Brushes: 20pcs/box*1
Color:
Enamel color: A2, ICL, IBU, IAM
Dentin color: A2
FEATURES & ADVANTAGES:
Unique dispersion technology ensure the filler evenly distributed
Radioopaque and fluoride releasing Optimal polishability and high shade stability.
Excellent handling, not sticky to instrument; Suitable for most cases of restoration, extensive indication of usage.
Total-Etching type
D
escription
Orthodontic Adhesive: Designed for bonding of metal and ceramic brackets on enamel.
It is of high viscosity and thus prevents bracket drifting and reduces material waste.
As it is light cured extra working time is ensured and therefore accurate bracket placement can be obtained.
INDICATIONS FOR USE: Direct bonding of metal and ceramic brackets
Packing list:
Orthobond Light Cure Adhesive Primer  6ml*1 bottle;
Etching Gel  5ml*1 syringe;
Light Cure Adhesive Paste 4g*3 syringe;
Little brush 20;
Syringe tip:5
STORAGE: Store at 25℃
or less in a cool and dry place and avoid direct sun exposure. Recap the syringe after use.
FDA Statement
The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory agencies. If so, you can bid on this item only if you are an authorized purchaser. If the item is subject to FDA regulation, I will verify your status as an authorized purchaser of this item before shipping of the item.
Seller name:Dentaljoy
City,State:SHENZHEN,China
Telephone number:0755-67530378
Re: K192233
Trade/Device Name: LED Curing Light
Regulation Number: 21 CFR 872.6070
Regulation Name: Ultraviolet Activator for Polymerization
Regulatory Class: Class II
Product Code: EBZ
Dated: December 7, 2019
Received: December 16, 2019
K180463
Trade/Device Name: Apoller Flow Light Cure Flowable Composite
Regulation Number: 21 CFR 872.3690
Regulation Name: Tooth Shade Resin Material
Regulatory Class: Class II
Product Code: EBF